Luxury and Modern Indoor Kitchens | Indoor Kitchens Boffi XO (2024)

WOOD LACQUERED LASERMAT GLASS STAINLESS STEEL METAL OF DE CASTELLI CORIAN® COMPOSITE CLAY STONE-MARBLE-GRANITE ALUMINIUM

Coated with high quality resin.The Boffi melamine-coated carcasses have the structure made of wood suitable for humid environments for internal useparticle board panel with low formaldehyde emission.Only for carcass.

Metal-effect lacquer. Easy Metals is a finishing that reproduces the typical effect of metallic surfaces, obtained by use of metal particles-enriched solvent-based paints.Variations in brightness (halos caused by the spread of the paint metal particles along the surface) make each piece a unique and exclusive.

Nanotechnological matt “soft touch” FENIX NTM® surface.FENIX NTM®The exterior decorative surface is obtained starting from thermosetting last generation resins that, thanks to the use of nanotechnology (NTM), make the surface extraordinary from a mechanical, aesthetic and functional point of view.FENIX NTM® UNICOLORObtained starting from thermosetting last generation resins that, thanks to the use of nanotechnology (NTM), make the surface extraordinary from a mechanical, aesthetic and functional point of view (colour-core).

Water-based textured matt lacquer.The following features make SILCOLAK a top-quality finish:• Water-based textured paint, bi-component and undiluted (not contaminated by external agents), designed and produced exclusively for Boffi.• Colour range, exclusive for Boffi.• Excellent chemical and physical resistance (tested in laboratories).• Very low yellowing effect over time.• Coat of isolating paint Primer and double layers of polyester plastering, ideal for reducing small imperfections on surfaces and allowing a better coverage.• Base coat of polyester.• Coat of isolating paint Primer for corners and edges.• Two paint coats, cross-applied.

Water-based “soft touch” matt lacquer.Features:The following features make ECOLAK a top-quality finish:• Water-based “soft touch” paint, bi-component and undiluted (not contaminated by external agents), designed and produced exclusively for Boffi.• Colour range, exclusive for Boffi.• Excellent chemical and physical resistance – tested in laboratories.• Very low yellowing effect over time.• Coat of isolating paint Primer and double layers of polyester plastering, ideal for reducing small imperfections on surfaces and allowing a better coverage.• Base coat of polyester.• Coat of isolating paint Primer for corners and edges.• Two paint coats, cross-applied.

Boffi uses only wood from not primary forests, to guarantee an adequate restoration of the renewable raw materials.

Slats, alternating thickness 20 / 23 mm - Solid wood layers, with support made of strip wood. Boffi uses only wood from not primary forests, to guarantee an adequate restoration of the renewable raw materials. Doors and panels have vertical grain.The “old“ grey pinewood consists of pinewood solid boards recycled from renovation of old houses, barns and huts. The characteristic grey tone of this material is obtained by specific painting cycles, which give the typical “old” aspect to this wood.Possible cracks and deformations have to be considered characteristic part of the product. Since these pieces are very unique, they have the typical appeal of “imperfect things“ and they clearly display sign of times and bad weather; therefore they show deformations and wrinkles strength. Worktops obtained with old wooden boards offer a clear example of the wood vitality and instability. For this reasons each piece in solid wood has to be considered considered “unique“ and different from all the other ones.

The polyester lacquering is carried out by a process of applying paints on MDF panels, with several coats. The surfaces are sanded with different coarse-grained and fine-grained sandpapers. Then they are polished using brushes impregnated with abrasive wax.The result obtained is a very glossy surface (close to the mirror effect) that reaches 95 gloss. Polyester is a very resistant material, practically waterproof; its surface does not absorb, but is sensitive to scratches. The scratched surface can be re-smoothed and re- polished or even repaired adding material and then by sanding and smoothing it again.Three layers of paint coat each surface, it means 900 g/m2 (ca. 1 mm thick); nine layers of paint coat each edge (ca. 3 mm thick). It is sensitive to light if directly exposed for very long periods. It can slightly change the tone, becoming lighter especially on light tones (family of whites).In case of element additions in a second moment, these tone changes cannot be perfectly replicated and may not match exactly the original shade. This issue cannot be considered cause for a complaint.

Wood layers, with support made of strip wood. Boffi uses only wood from not primary forests, to guarantee an adequate restoration of the renewable raw materials. Doors and panels have vertical grain.The “old“ grey pinewood consists of pinewood solid boards recycled from renovation of old houses, barns and huts. The characteristic grey tone of this material is obtained by specific painting cycles, which give the typical “old” aspect to this wood.Possible cracks and deformations have to be considered characteristic part of the product. Since these pieces are very unique, they have the typical appeal of “imperfect things“ and they clearly display sign of times and bad weather; therefore they show deformations and wrinkles strength. Worktops obtained with old wooden boards offer a clear example of the wood vitality and instability. For this reasons each piece in solid wood has to be considered considered “unique“ and different from all the other ones.

Tempered glass 4mm

AISI 304 stainless steel sheet, solid wood edge.Edge feasible in: American elm SW / Canaletto LIGHT walnut (without “sawn effect”) / Olivato ash wood SW / Thermo-treated Olivato ash wood SW / Smoked dyed oak SW.

AISI 304 box section stainless steel sheet.

AISI 304 box section stainless steel sheet, orbital satin (Orbital Steel). It is an irregular steel grain pattern, obtained by using an orbital sander which gives the stainless steel a vintage look. EXCLUSIVE FINISH FOR BOFFI

AISI 304 stainless steel sheet, orbital satin (Orbital Steel), solid wood edge.Edge feasible in: American elm SW / Canaletto LIGHT walnut (without “sawn effect”) / Olivato ash wood SW / Thermo-treated Olivato ash wood SW / Smoked dyed oak SW.

Exclusive-appearance metal sheet obtained with special chemical and / or mechanical treatments.For generations the “mission” of De Castelli has been to enhance the natural metals such as iron, steel, brass and copper, making them unique thanks to dedicated and sophisticated mechanical or chemical treatments.The chromatic and aesthetic effects created are peculiar and highly distinctive. The metals of De Castelli are protected only by transparent paints, in full respect of the core of the metal used.

Boffi uses only wood from not primary forests, to guarantee an adequate restoration of the renewable raw materials.

It is a Solid Surface, non-porous and hom*ogeneous, composed for about 1/3 of acrylic resin (polymethyl methacrylate or PMMA) and for about 2/3 of natural minerals consisting mainly of aluminium trihydrate (ATH), which is a mineral extracted from the bauxite used to produce aluminium.

Very compact surface composed of quartz, materials used to produce glass and ceramic, treated with Sinterized Particle Technology and ultra-compaction process.

Composite material made of high-purity minerals, by using Full Digital technology. “Natural” matt finish.The decorative design is on the front surface only.Features:- Surface: smoother-feeling texture and total control over the design, leading to outstanding visual properties.- Hygienic and nontoxic: Because it has a non-porous surface, this prevents the build-up of bacteria or mould.- Resistant: It is highly resistant to stains, heat, frost, thermal shock, scratches and impacts, ultraviolet rays and has a low water absorption rate.- Ecological: -70% savings on water consumption and -90% reduction in atmospheric emissions during the production process. 50% made with recycled materials.

Raw clay mixed with resin. The compound is applied by hand with a spatula, creating a very elegant and refined texture that is exclusive and unique for each surface.The manual trowelling may generate slight differences in thickness on the finished product. This process makes each piece unique and unrepeatable.

Natural material extracted from quarry. Matt finish. The natural stones used by Boffi for the production of tops, panels, back panels, sinks, washbasins or bathtubs are always given a dedicated stain and oil-repellent and waterproof treatment to guarantee a high protection.

Aluminium sheet. Epoxy powder-coated finish.

Metal-effect lacquer.Metals is a special finishing which reproduces the typical effect of brushed metallic surfaces, rendered through a very precise and technical sequence of production cycles. The characteristic metallic effect of the surface is given by the alternation of manual and mechanical processes, by the quality of the metal particles-enriched solvent-based paints and by the complex drying procedure.The various shades of colour (halos caused by the spread of the paint chromium particles) and the succession of multi-directional brushing of the surface make each piece a unique and exclusive one.

Veneer reconstructed textured Eco-wood. Finished with water-based paint. Boffi uses only wood from not primary forests, to guarantee an adequate restoration of the renewable raw materials.

Solvent-based matt lacquer.Features:• Solvent-base polyurethane coating• Base coat of polyester.• One paint coat, cross-applied